HomeGrowBible · Measurements

Measurements 158

Every number Dakota speaks aloud — VPD, PPFD, EC, dosages, timings, dimensions — with episode-attributed context.

AutoPot establishment time before activating system: 10–14 days post-transplant cultivation

AutoPot guidelines read by Dakota: allow plants to hand-water settle-in for at least 10–14 days before turning the automated water system on.

Ep 001

Planned veg duration (45-day target set in Pulse): 45 days cultivation

Dakota set a 45-day veg phase in the Pulse app as a progress bar guide for the new seedling batch.

Ep 001

Previous CO2 run veg duration before flower flip: 12–30 days cultivation

Mr. Q referenced Dakota previously flipping plants to flower after only 12 days veg with CO2, then revised to 'about 30 days.' Dakota confirmed '12 days right in flower before.'

Ep 001

Recommended plant size for AutoPot potting up: ~12 inches tall cultivation

AutoPot guidelines specify plants should be 'properly established, around 12 inches tall' before transplanting into AutoPot system. The channel's seedlings were smaller than this at time of first transplant.

Ep 001

Seedling age at time of transplant: 12 days from germination cultivation

Mr. Q assessed the seedlings at 12 days and said they were 'really time already' for transplant, noting roots were at the sides and bottom of the starter plug.

Ep 001

CO2 controller shutoff setpoint: 800 PPM environment

CO2 flow turns off once the room exceeds 800 PPM; exhaust fans stay off during lights-on except for one 5-minute cycle after lights out

Ep 004

CO2 level at commissioning: 779 PPM rising to 800 PPM environment

First CO2 sensor reading after tank was opened; controller setpoint is 800 PPM, at which flow shuts off

Ep 004

CO2 level — day 11 veg: 1100 PPM environment

CO2 reading slightly elevated because crew had been working in the room for 20 minutes; system otherwise functioning correctly

Ep 004

CO2 room dimensions: 15 ft x ~7.5 ft environment

Dakota describes the CO2 room as '15 ft by about 7 and 1/2 ft' when planning the 24-pot Autopot layout

Ep 005

CO2 room veg day at end of episode: Day 20 veg environment

CO2 room clones confirmed at veg day 20 at the episode's closing segment, with 1–2 more weeks of veg planned before flipping to flower.

Ep 001

CVault curing humidity target: 59% environment

Target humidity inside the CVaults at the start of the curing process. Dakota describes this as 'perfect.'

Ep 002

CVault humidity at smoke test (Mr. Q reading): 62%, rising to 63–65% environment

Mr. Q reads the CVault humidity upon opening it for the post-harvest smoke session, noting it was still 62% and climbing. He calls this his preferred curing range.

Ep 002

Days in flower at harvest: Day 56 environment

The large indoor flower room with all Battle of the Breeders strains was on day 56 of flower at harvest time.

Ep 003

Dome VPD during crisis: 1.5 VPD environment

Measured inside propagation domes using AC Infinity VPD gun; far above ideal clone VPD range; caused clone death

Ep 004

Dry room target humidity: ~60% environment

Target relative humidity in the dry room during the 14-day drying period after harvest.

Ep 002

Dry-back target percentage: 30–35% environment

VWC allowed to drop 30–35% from field capacity before the next automated irrigation event is triggered

Ep 004

EVO light setting in 2x4 (veg day 18): 30% environment

EVO set to 30% in the 2x4 at veg day 18, approximately 3 ft from the canopy; described as looking 'perfect.'

Ep 001

EVO light setting in 2x4 propagation (seedling stage): Level 2 environment

Set to level 2 for pre-emergence seedlings ~3 ft above the tray.

Ep 001

EVO light setting in CO2 room (during PPFD check): Level 5 environment

Light was turned up to level 5 at the end of the CO2 room PPFD check, producing 500 µmol at center canopy.

Ep 001

EVO3 light power setting during grow: 70–80% (never 100%) environment

The IONFRAME EVO3 LED was only ever set to 70–80% power throughout the entire Kerosene Krash grow and still produced 0.8 g/w yield.

Ep 002

Exhaust fan runtime during CO2 period: 5 minutes once per lights-out cycle environment

Exhaust fans disabled during lights-on to maintain CO2; run once after lights out for fresh air exchange

Ep 004

Granny Candy plant height at day 21 flower: ~6 ft environment

Mr. Q estimated the Granny Candy plants at approximately 6 feet tall, noting other greenhouse plants reached 7–8 feet.

Ep 001

Greenhouse flower day at defoliation session: Day 21 environment

The greenhouse had been in flower for 21 days (3 weeks) at the time of the defoliation and walkthrough session.

Ep 001

Greenhouse nighttime humidity: 90%+ environment

Mr. Q cited 90% or higher nighttime humidity as justification for aggressive defoliation in the greenhouse to maintain airflow and prevent mold.

Ep 001

Highest recorded propagation humidity (recent): 64% RH environment

Described as the highest humidity seen in over a week in the propagation room before the humidifier arrived

Ep 004

Humidifier power level setting: Level 7 environment

Initial test setting on the CloudForge T7; to be adjusted throughout the day

Ep 004

Humidifier target humidity setpoint: 70% RH environment

Controller 69 set to auto-activate CloudForge T7 when RH drops below 70% in propagation room

Ep 004

Indoor grow tent / room size: 4x8 feet environment

The large flower room housing all Battle of the Breeders strains was described as a 4x8.

Ep 003

LED intensity setting post-transplant: Setting 2 (~250 PPFD) environment

Evo 10 LEDs set to level 2 immediately after transplant into CO2 room

Ep 004

LED intensity setting — veg ramp: Setting 3 (~350 PPFD) environment

Planned step-up 1–2 days post-transplant to increase light intensity during veg

Ep 004

Light height above canopy: 4 feet environment

Evo 10 LEDs hung approximately 4 feet above the plant canopy during early veg

Ep 004

Maximum allowed propagation room temperature: 30°C environment

Dakota sets Terraform 7 to prevent temps rising above 30°C inside the clone room

Ep 004

Mother greenhouse LED panel wattage: 100 watts each (5 panels = 500 watts total) environment

'These panels are 100 watts each and it's totally overkill. Like that's 1 2 3 4 500 watts' — running from 6 pm to midnight to keep moms in veg

Ep 005

Mother greenhouse light-on time: 6:00 PM to midnight environment

Five 100W panels in the mother greenhouse turn on at 6 pm and off at midnight to supplement daylight and prevent flowering

Ep 005

PPFD at 10 inches above canopy level (CO2 room): 700 µmol/m²/s environment

Mr. Q demonstrated that raising the sensor 10 inches above canopy level increased PPFD by ~200 µmol, illustrating the importance of consistent measurement height.

Ep 001

PPFD at canopy center (CO2 room, light at level 5): 500 µmol/m²/s environment

Measured at center of CO2 room canopy with light at level 5; Mr. Q noted this is 'definitely enough for veg when they're that small.'

Ep 001

PPFD at canopy edges (CO2 room, light at level 5): 400–420 µmol/m²/s environment

Measured at the sides/edges of the CO2 room canopy with AC Infinity light set to level 5.

Ep 001

PPFD at canopy — day 3 flower: ~800 µmol/m²/s environment

Measured in the middle of the canopy at day 3 of flower; Evo 10s on setting 7; discussed increasing further

Ep 004

PPFD at seedling propagation tent (level 3, at plant height): 300 µmol/m²/s environment

Mr. Q measured 300 µmol at the seedling canopy level with EVO set to level 3, calling it 'fucking perfect' for 12-day-old seedlings.

Ep 001

PPFD at sides of propagation tent (level 3): 220–250 µmol/m²/s environment

Edges measured lower at 220–250 µmol versus center 300 µmol in the seedling tent.

Ep 001

PPFD in greenhouse shaded parts (noon, still partially cloudy): 1,200–1,250 µmol/m²/s environment

Measured near the exit of the greenhouse on the shady side as the sun was approaching noon but not fully out. Mr. Q: 'We immediately have 1,200 PPFD even here in the shady parts.'

Ep 001

PPFD in propagation tent (light at level 2, ~3 ft above seedlings): 150–170 µmol/m²/s environment

Edges measured at ~150, center at ~170 µmol for pre-emergence seedlings. Dakota noted this is acceptable until seeds pop above soil.

Ep 001

PPFD inside greenhouse brighter area (approaching noon, clouds still present): 600 µmol/m²/s environment

Mr. Q measured 600 µmol in the area where plants historically get largest; Dakota noted this is where the Chicken & Waffles was previously grown.

Ep 001

PPFD inside greenhouse shaded side (overcast approaching noon): ~400–450 µmol/m²/s environment

The right/shaded side of the greenhouse measured lower, around 400–450 µmol; Mr. Q commented this was 'lower than I thought.'

Ep 001

PPFD outdoors at full noon sun: 2,000–2,500 µmol/m²/s environment

Historical maximum outdoor PPFD measurement confirmed by both Dakota and Mr. Q.

Ep 001

PPFD outdoors overcast / partial cloud: 1,000–1,300 µmol/m²/s environment

Measured outside the greenhouse on an overcast day approaching noon; Mr. Q noted '1,000 is like the max you could have indoors' and the reading was climbing as clouds moved.

Ep 001

Propagation room temperature (normal target): 25°C / 45% RH environment

Readings on the room sensor at the time of reporting the clone deaths; humidity too low alongside too-high temperature

Ep 004

Propagation room temperature during crisis: 35°C environment

Measured with a heat gun after the clone kill event; Dakota notes it was way too hot and triggered the purchase of the Terraform 7 AC unit

Ep 004

Stem diameter (Punch & Punch F2): ~2 inches environment

Mr. Q estimated the Punch & Punch F2 stem at approximately 2 inches in diameter, commenting it 'could easily be 15–20 oz.'

Ep 001

System water pressure (maintained): 40 PSI environment

Maintained system pressure during active drip delivery; described as 'perfect' for the drip system

Ep 004

System water pressure (pump): 60–70 PSI environment

Measured at the 3/4-inch gauge directly off the pump during initial irrigation tests

Ep 004

Target PPFD for seedlings after emergence: 200 → 300 µmol/m²/s (ramping up) environment

Dakota planned to ramp light from 150–170 to 200, then 300 µmol/m²/s as seedlings emerged and developed.

Ep 001

Terraform 7 cooling trigger temperature: 26°C environment

AC unit switches on automatically when room reaches 26°C

Ep 004

VWC after first watering (4x8 post-transplant): 30% environment

Pulse sensor reading in the 4x8 coco substrate immediately after the first hand-watering at veg day 18.

Ep 001

VWC before first watering (4x8 post-transplant): 15% environment

Pulse sensor reading in the 4x8 coco substrate prior to the first hand-watering at veg day 18.

Ep 001

VWC in 2x4 planter box (veg day 18): ~14% environment

Pulse app showing 2x4 sitting at about 14% VWC at veg day 18; plants were perky and not yet needing water.

Ep 001

AutoPot coco buffering protocol water volume: 2.5 gallons per pot nutrient

AutoPot's guideline: run 2.5 gallons of pH 5.6 water with quarter-strength feed through each pot to stabilize coco before activating automated system.

Ep 001

Autopot coco/perlite substrate ratio: 30% perlite / 70% coco nutrient

'We're going to run perlite on this next batch, about 30% perlite, 70% coco' for the CO2 Autopot run

Ep 005

Feed pH during active drip irrigation: 5.6 nutrient

pH set for the ongoing drip feeds into coco during early veg in the CO2 room

Ep 004

Feeding frequency at day 11 flower: Every second day nutrient

Plants were being fed every other day at approximately 1.5 liters per feeding at day 11 flower, with plans to increase volume.

Ep 002

Feeding volume at day 11 flower: ~1.5 liters per feeding nutrient

Volume fed every second day during early flower (day 11). Expected to increase as plants develop.

Ep 002

Hand-watering volume prepared (veg day 18): 20 liters nutrient

Dakota mixed 20 L of Cronk Intermediate Plan nutrient solution for the first hand-watering of the 4x8 post-transplant.

Ep 001

Pre-saturation coco media EC: 3.5 EC nutrient

EC of the initial nutrient solution used to pre-condition the coco media before transplant

Ep 004

Pre-saturation coco media pH: 5.5 to 5.8 nutrient

Target pH range for the initial coco pre-soak feed before transplanting clones into CO2 room pots

Ep 004

pH of Cronk hand-watering solution (4x8 tent, veg day 18): 5.8 nutrient

Dakota mixed 20 L of Cronk Intermediate Plan; solution came out to pH 5.8 without needing pH up or down.

Ep 001

pH target for CO2 room (100% coco): 5.6–5.8 nutrient

Dakota confirmed the CO2 room was being fed at pH 5.6–5.8, noting coco is run slightly lower than soil.

Ep 001

Amendments + mycorrhizae per raised bed: 100–250 kg combined other

Combined weight of mycorrhizae and organic amendments added to each of the 7 main beds

Ep 004

Athena handbook price: $20 (or free download) other

The Athena Cultivation handbook is available on the Athena website for $20 or as a free digital download.

Ep 002

AutoPot reservoir size for CO2 room: 105 gallons other

'We got the 105-gallon. I believe this is the pro.' Selected for the 24-plant CO2 Autopot run.

Ep 005

Blood Moon Gelato pheno #2 estimated flower time: ~75 days other

Pheno #2 still needs more time at day 66; Dakota estimates ~75 days total flower time for this pheno

Ep 005

Bloogatti pheno #5 flower time: 55 days other

Pheno #5 of Bloogatti was ready to harvest at only 55 days flower — the fastest in the CO2 run

Ep 005

CO2 room Autopot setup size: 24 pots other

'Total 24 plant 24 pot Autopots setup' planned for the CO2 room next run

Ep 005

CO2 room harvest day: Day 66 flower other

All CO2 room plants (except one longer-finishing pheno) harvested at day 66 flower

Ep 005

Clone success rate with Athena: 100% other

Dakota reports hitting 100% clone success rate every single time since switching to Athena's cloning gel and SOPs.

Ep 002

Clones delivered by Mr. Q: 200 clones other

Mr. Q delivers 200 rooted clones to the farm for planting into the greenhouse beds

Ep 004

Coco fiber per raised bed: 300 kg other

Amount of coco fiber mixed into each of the 7 main greenhouse raised beds

Ep 004

Cvault cure duration: 10 days other

'Literally just seal her up 10 days, she's cured' — using Vevi Cure packs, no burping

Ep 005

Dakota's bag appeal rating — Kerosene Krash: 8.5/10 other

Dakota's bag appeal score, noting very green buds with no purple but exceptional frost coverage.

Ep 002

Dakota's overall effect rating — Kerosene Krash: 9.8/10 other

Dakota's score for effects strength and quality of Kerosene Krash during personal pre-session testing.

Ep 002

Discount savings via channel code on Seedsman: 10% other

Sponsor mention in episode description: 'SAVE 10% on Genetics with code HomeGrowTV on Seedsman.'

Ep 003

Drip tape lines per bed: 4 lines per bed other

'Every single bed has four lines of drip tape' running the full length of each bed

Ep 005

Dripper flow rate: 100 ml per minute other

Measured per dripper line during 2-minute calibration test for the CO2 room drip system

Ep 004

Dry duration in dry room: 14 days other

Buds were dried in the AC Infinity dry rack in the dry room for approximately 14 days before transferring to CVaults.

Ep 002

Dutch Passion founding year: 1987 other

Year Dutch Passion was officially formed in Amsterdam by Hank van Allen.

Ep 002

Dutch Passion years in business: 37 years (founded 1987) other

Dakota states Dutch Passion has been in the game for over 37 years, established in Amsterdam in 1987.

Ep 002

End of veg / flip to flower: Day 56, end of week 8 other

Final veg update before flipping to flower. Both phenos healthy with even canopy achieved.

Ep 002

Feed volume per event: 150–300 ml other

Volume delivered per 1–2 minute drip event per pot in early veg coco management

Ep 004

Feminized seed invention year: 1997 other

Year Dutch Passion claims to have invented feminized seeds.

Ep 002

Flower day at first update: Day 11 flower other

First flower update; plants looking happy, stretch beginning, internodal spacing assessed as tight and promising.

Ep 002

Flower day at mid-flower update: Day 24 flower, week 4 other

Second flower update; first trichome development visible, initial sweet/sherbet-leaning aromas detected.

Ep 002

Flower day at return from Humboldt trip: Day 67 flower, week 10 other

First in-tent update after 43 days away at the Humboldt Seed Company pheno hunt. Massive trichome and bud development observed.

Ep 002

Germination duration: 48–72 hours other

Time from placing seeds on cotton pads in sealed Ziploc bag to taproot emergence using the cotton pad method.

Ep 002

Giveaway prize value: $100 AC Infinity store credit other

Monthly giveaway prize: $100 AC Infinity gift certificate for winner Enmity NZ4613

Ep 005

Greenhouse bed count: 8 beds other

Eight living soil beds total in the main greenhouse, each planted with a different genetic except Marji's Magic which has two beds

Ep 005

Greenhouse bed fill team size: 7 people, ~5 days other

Team of 7 strong crew members worked approximately 5 days to fill all 8 raised beds; not even halfway after day 1.5 without the Bobcat

Ep 004

Greenhouse bed plant count: 50 plants per bed other

Current greenhouse run uses 50 seeds per bed for pheno hunting, compared to 30 plants/bed in the previous run

Ep 005

Greenhouse veg day at time of filming: Day 14 veg other

'By the way, we're in day 14 veg right now in the greenhouse'

Ep 005

Hang dry duration (tent harvest): 10–13 days other

Target hang dry time for Blood Moon Gelato, Peyote Zkittlez, and Mellowz before moving to Cvault cure

Ep 005

Lab testing cost (previous method): $100 per sample other

Cost of sending samples to a certified laboratory in Colombia for full cannabinoid and terpene analysis—the method replaced by the Purple Pro after the lab closed.

Ep 002

Main outdoor water reservoir size: ~8,000 L other

'Our main res tank, right? This is I think around 8,000 L' — feeds gravity irrigation to all greenhouse beds

Ep 005

Marji's Magic pheno hunt seed count: ~100 seeds (2 beds) other

'About 100 seeds of the Marji's Magic sitting right behind me right here' across two full beds

Ep 005

Mellowz pheno #1 estimated finish: ~Day 60 other

Mellowz #1 described as 'decently fast mid flower, I would say day 60-ish'

Ep 005

Mellowz tent room flower day at filming: Day 63 flower other

Pulse batch tracker showed day 63 in the Autopot tent room / Mellowz grow at time of greenhouse filming

Ep 005

Morning feed frequency and interval: ~9 feeds, 15 minutes apart other

During lights-on period, approximately 9 drip events spaced 15 minutes apart, each running 1–2 minutes (150–300 ml per event)

Ep 004

Mr. Q's bag appeal rating — Kerosene Krash: 8.2/10 other

Mr. Q independently scores bag appeal at 8.2, saying it looks like dispensary quality.

Ep 002

Mr. Q's overall rating — Kerosene Krash: 8/10 other

Mr. Q's overall combined rating: 'more or less eight on eight over ten, this is definitely approved.'

Ep 002

Number of seeds germinated: 400+ other

Described as the most genetics ever popped at one time at the Home Grow TV farm for the greenhouse season

Ep 004

Nutrient mixing reservoir size: 2,000 L other

Secondary tank filled from the main 8,000 L tank; used to mix and deliver weekly Kronk nutrient batches

Ep 005

Official harvest day: Day 73 flower other

Six days after the day 67 trichome check, Dakota determined it was time to harvest both Kerosene Krash phenotypes.

Ep 002

Open Sprinkler setup time: ~15 minutes other

Time taken to complete full Open Sprinkler + Pulse integration setup from scratch

Ep 004

Paco's number of return visits to shoot Battle of the Breeders flowers: 4th time back (5th day total) other

Dakota asked Paco 'this is your fourth time back shooting flowers now on Battle of the breeder stuff right' and Paco confirmed 'fourth no fifth day.'

Ep 003

Pheno hunt plant count at Humboldt: 10,000–20,000 plants other

Estimated number of total plants viewed across multiple farms during the Humboldt Seed Company Mega Pheno Hunt in the Emerald Triangle.

Ep 002

Photography session duration (first night): Until approximately 12:30 AM other

Paco reported shooting '360s till like 12:30 or so till the battery died' on the first night of the two-day content session.

Ep 003

Pink Paloma seeds — germination success: 3 of 5 other

From a pack of 5 Pink Paloma seeds from Raw Genetics, 3 turned out looking good for transplant into CO2 room

Ep 004

Pulse Zero price: $129 other

Launch price of the new Pulse Zero environmental monitor, described as the most affordable entry point into the Pulse ecosystem.

Ep 002

RO filter initial flush duration: 45 minutes other

Required to clear food-grade preservatives from the new Ecojet 110 filter before putting water into plant use

Ep 004

Rice hulls cost: $15 USD per bale other

Purchased from a local Colombian garden center for the re-transplant substrate mix.

Ep 001

Seed pack price (3-pack, per bean): ~€30 per bean in 3-pack (~€90 total) other

Dakota notes the 3-pack brings the per-bean cost to about €30 each, still describing it as 'most certainly not a cheap strain.'

Ep 002

Seed pack price (single bean): €50 per bean individually other

Price Dakota references for a single Kerosene Krash bean from Dutch Passion's website—their most expensive genetic.

Ep 002

Seedling stage in Solo cups: 28 days (day 28 veg) other

Duration plants remained in Solo/Dixie cups before showing signs of needing transplant (drying out almost daily).

Ep 002

Seedsman founding year: 2002 other

Year Seedsman began operations; cited by Dakota as evidence of their trustworthiness as a seed source with over two decades in business.

Ep 002

Soil cost: $220 per truck load other

Cost of one large truck delivery of natural earth soil used as the raised bed base; described as the cheapest solution available

Ep 004

Soil weight per raised bed: ~2 tons other

Approximate total weight of the natural earth substrate per bed

Ep 004

THC potency test — first sample: 19% other

First Purple Pro at-home cannabinoid test result on the Kerosene Krash after calibration.

Ep 002

THC potency test — second sample: 21% other

Second Purple Pro cannabinoid test result on the Kerosene Krash. Dakota notes 20%+ is his benchmark for satisfaction.

Ep 002

THC threshold for Dakota satisfaction: 20%+ other

Dakota states 'anytime I hit anything above 20 I'm happy' as his personal potency benchmark when using the Purple Pro.

Ep 002

Target runoff volume per pot: 150 ml (2% of 2-gallon pot) other

Target runoff for pre-saturation of 2-gallon coco pots before transplanting; total ~4.5 L for both beds

Ep 004

Tent room (4x8) harvest day: Day 66 flower other

Blood Moon Gelato and Peyote Zkittlez harvested at day 66 in the 4x8 tent

Ep 005

Time away from farm before harvest visit: 1 month (approximately 3 weeks in California + additional travel) other

Dakota stated 'we haven't been here for a total of 1 month' and detailed 3 weeks in California plus stops in Amsterdam and Morocco.

Ep 003

Total days away / gap in veg updates: 43 days other

Period between day 24 flower update and returning from the Humboldt Seed Company Mega Pheno Hunt trip to find plants at day 67 flower.

Ep 002

Total media volume pre-saturation run: Over 150 litres other

Total nutrient solution used to fully saturate both beds of coco before first transplants; approximately 1.5 reservoir fills

Ep 004

Veg duration (planned vs actual): 21 days planned, potentially cut to 14 days other

Dakota originally planned 21-day veg in CO2 room but notes growth is so accelerated at day 11 he may flip to flower at 14 days

Ep 004

Vegetative period at topping: Day 50 veg, beginning of week 8 other

Timing of topping the tall phenotype—22 days after transplant from Solo cups, at the start of week 8 veg.

Ep 002

Watermelon Emoji flower time: 7 weeks other

Mr. Q states the Watermelon Emoji #22 (Copat Genetics) finishes in only 7 weeks of flower

Ep 004

Rice hulls aeration ratio: 30% of substrate volume substrate

AutoPot's team recommended adding 30% aeration amendment to coco; Dakota used rice hulls at this ratio for the re-transplant.

Ep 001

Auto Kong #4 THC content: 17% THC terpene

Lab-tested THC percentage reported by Mr. Q for the Auto Kong #4 sample

Ep 004

Auto Kong #4 terpene content: 4% terpenes terpene

Lab-tested total terpene percentage reported by Mr. Q for the Auto Kong #4 sample

Ep 004

Dakota's aroma/breakup rating — Kerosene Krash: 8/10 terpene

Dakota's score for the aroma upon breaking up the Kerosene Krash buds.

Ep 002

Dakota's taste rating — Kerosene Krash: 8.5/10 terpene

Dakota's taste score for Kerosene Krash despite it not being his personally preferred flavor profile.

Ep 002

Mr. Q's burn/taste rating — Kerosene Krash: 8/10 terpene

Mr. Q scores burn quality and taste at 8/10, noting white ash, smooth smoke, nobody coughing.

Ep 002

Mr. Q's smell rating — Kerosene Krash: 7.5/10 terpene

Mr. Q scores smell at 7.5, noting you cannot smell it from across the room though it smells nice up close.

Ep 002

Terpene spider chart citrus score — Kerosene Krash: 0/5 terpene

Dakota scores zero for citrus notes on Kerosene Krash.

Ep 002

Terpene spider chart dank score — Kerosene Krash: 4/5 terpene

Dakota's score for cedar, pine, musky terpene character in the Dank category.

Ep 002

Terpene spider chart dessert score — Kerosene Krash: ~2/5 terpene

Dakota's estimated score for chocolate back notes in the Dessert category, noted as hard to find.

Ep 002

Terpene spider chart earthy score — Kerosene Krash: 5/5 terpene

Dakota's score for Kerosene Krash in the Earthy terpene category (herbal, floral, minty, menthol, peppery, woody, spicy). Described as 'very very Woody' with some minty notes.

Ep 002

Terpene spider chart fruity/tropical score — Kerosene Krash: 0/5 terpene

Dakota scores zero for fruity and tropical notes—no fruit, no tropical, nothing in this category.

Ep 002

Terpene spider chart pungent score — Kerosene Krash: 2/5 terpene

Dakota's score for skunky, gas, diesel notes in the Pungent category.

Ep 002

Auto Kong #4 yield: 170g+ dry flower yield

Mr. Q reports the Auto Kong #4 from Paradise Seeds produced more than 170g dry, with 150g still remaining in the jar after sampling

Ep 004

Gram per watt efficiency: 0.8 g/w yield

Calculated by Dakota at approximately 0.8 grams per watt, achieved with EVO3 running at only 70–80% power. Described as one of the channel's best producers in a 2×4.

Ep 002

Harvest weight — CVault #1: 61.8 g yield

Dried, cured flower weight from CVault #1 (one phenotype) of the Kerosene Krash run in the 2×4 tent.

Ep 002

Harvest weight — CVault #2: 123 g yield

Dried, cured flower weight from CVault #2 (second phenotype) of the Kerosene Krash run—the heavier producer.

Ep 002

Harvest weight — popcorn nugs jar: 30 g yield

Weight of smaller popcorn nugs collected separately in a third jar from the total harvest.

Ep 002

Number of Emerald Fire OG autoflowers in greenhouse run: 50 yield

'these are all going to be going into the greenhouse 50 Emerald fires from The Humble Seed Company'

Ep 003

Number of favorite phenotypes selected for studio shoot: Approximately 20+ yield

Dakota said 'here's the list of our favorite fenos I think it's about 20 something plus we're going to shoot all the baby Yodas and all the Nerds Rope.'

Ep 003

Number of plants in greenhouse: ~250 yield

Mr. Q noted the current run has approximately 250 plants, compared to 500 on a previous run, but the individual plants are much larger this time.

Ep 001

Number of plants planned for greenhouse: 400–500 plants yield

Total plants across 8 raised beds; approximately 60–65 per bed

Ep 004

Plants per raised bed: ~60–65 yield

Target density per bed in the greenhouse raised bed system

Ep 004

Total harvest weight: 215.6 g yield

Combined total of both CVaults (61.8 g + 123 g) and popcorn jar (30 g) from two Kerosene Krash plants in a 2×4 tent.

Ep 002